| Customization: | Available |
|---|---|
| Driving Type: | Motor |
| Impeller Number: | Single-Stage Pump |
Suppliers with verified business licenses
Audited Supplier Audited by an independent third-party inspection agency
| Code | Material # | Hardness HRC |
Performance | Application |
| A05 | KmTBCr26 | ≥56 | Ranks second only to A07 in abrasion-resistant performance; fair corrosion-resistant performance. | High impact load abrasion condition; PH rate ranging from 5 to 12 |
| A07 | KmTBCr15Mo3 | ≥59 | Best abrasion-resistant performance; corrosion-resistant performance is inferior to A05 | High impact load abrasion condition |
| A33 | ≥35 | Abrasion-resistant performance is close to A03; fair corrosion-resistant performance | Oxide slurry with PH rate no less than 1, like phosphor-gypsum in phosphate fertilizer plant, nitric acid, sulph-oacid and phosphoric acid, etc. | |
| A49 | ≥43 | Fair abrasion-resistant performance, close to A03; fair corrosion-resistant performance in media with lower PH rate. | Corrosion conditions with low PH rate, especially for flue gas and FGD devices for media of PH≥4; general suitable for lower acid condition. | |
| A12 | ≥62 | Higher abrasion-resistant performance than A05; fair corrosion-resistant performance; suitable for media with PH rate is 6-16, where A05 is not suitable. | High abrasive slurry with fine particles. | |
| A61 | 63-68 | Optimized abrasion-resistant performance than A12 | High abrasive slurry with fine particles. |
| Material | Material # | Applications |
| Natural Rubber | R08 | R08 is low to medium hardness rubber used for impellers where slurry contains fine particles and erosive. |
| Natural Rubber(soft) | R26 | R26 is soft natural rubber used for liners where slurry contains fine particle and more erosive. |
| Natural Rubber(soft) | R33 | R33 is widely used for frame plate liners, cover plate liners and impellers. Max particle diameter is 10mm; impeller peripheral speed should be less than 25m/s; suitable for temperature not exceeding 75ºC. |
| Natural Rubber | R55 | R55 is widely used for impellers, frame plate liners, cover plate liners and throat bushes. Max particle diameter can be 20mm, impeller peripheral speed should be less than 27.5m/s; suitable for temperature not exceeding 75ºC. |
| EPDM Rubber | S01 | S01 is widely used for impellers, frame plate liners, cover plate liners and throat bushes. Max particle diameter can be 8mm; impeller peripheral speed should be less than 25m/s; suitable for temperature not exceeding 120ºC(continuous duty) or 140ºC(discontinuous duty). |
| Nitrile Rubber(NBR) | S12 | S12 is widely used for frame plate liners, cover plate liners, throat bushes, lip seals, impellers and expellers. Max particle diameter is 7mm; impeller peripheral speed should be less than 27m/s; suitable for temperature not exceeding 95ºC. |
| Butyl Rubber | S21 | S21 is widely used for impellers, frame plate liners, cover plate liners, expellers, volute seals and throat bushes,. Max particle diameter can be 7mm; impeller peripheral speed should be less than 30m/s; suitable for temperature not exceeding 100ºC. |
| Hypalon | S31 | S31 can be used for impellers, frame plate liners, cover plate liners and throat bushes,. It is recommended to use for strong acid slurry with mild or moderate corrosion. Max particle diameter can be 10mm; impeller peripheral speed should be less than 30m/s; suitable for temperature not exceeding 110ºC. |
| NAH series | L(R) ,M | HH | SP(R) | G | AF Series |
| 1.5/1B-NAH(R) | 20A-L | 1.5/1 C-HH | 40PV-SP(R) | 6/4D-G | 2QV-AF |
| 2/1.5B-NAH(R) | 50B-L(R) | 3/2D-HH | 65QV-SP(R) | 8/6E-G | 3QV-AF |
| 3/2C-NAH(R) | 75C-L | 4/3E-HH | 100RV-SP(R) | 10/8F-G | 6SV-AF |
| 4/3C-NAH(R) | 100 D-L | 4/3X-HH | 150SV-SP(R) | 10/8S-G | 8SV-AF |
| 6/4D-NAH(R) | 150E-L | 6/4F-HH | 200SV-SP | 12/10G-G | 2AHF |
| 6/4E-NAH(R) | 300S-L | 6/4X-HH | 250TV-SP | 14/12G-G | 3AHF |
| 8/6E-NAH(R) | 10/8 R-M | 6S-H | 14/12T-G | 4AHF | |
| 8/6R-NAH(R) | 10/8 E-M | 8/6S-H | 16/14 G-G | 6AHF | |
| 10/8F-NAH(R) | 12/10F-M | 8/6X-H | 16/14TU-GH | ||
| 10/8X-NAH(R) | 6S-HP | 16/14H-GH | |||
| 12/10ST-NAH(R) | 8/6S-HP | 18/16G-G | |||
| 14/12ST-NAH(R) | 8/6X-HP | 18/16 TU-GH | |||
| 16/14TU-NAH(R) | |||||
| 20/18G(TU)-NAH(R) |
| Factory Name | Shijiazhuang NaiPu Pump Co.,Ltd |
| Manufacturer or Trading Company | Manufacturer |
| Workshop | Foundry, Machining, Assembly |
| Year the company was established | 2007.01.10 |
| Number of employees | 162 |
| Designed capacity of factory | 3,000.T Resin Sand 2500T Lost Foam Casting 500T |
| Factory area in m2 | 330,000m2 |
| Does the factory record rejects. If so what is the reported reject rate for past 12 months. | Yes, We record. the reported reject rate for past 12 months =7.6% |
| Quality System Certification | ISO9001-2015, CE, |
| Types of Material the company produces | Ductile Iron Chrome Iron Alloy Steel Rubber |
| Melting Equipment | Induction 2T X 2 |
| Non destructive inspection equipment. | Ultrasonic testing equipment UT Dye penetrant testing PT |
| Typical products the foundry makes | Slurry Pump Wet End Parts Hydrocyclone Parts Wear resistant castings Other Wear Parts |
| Minimum and maximum casting weight for each moulding system | Max. 6.0T , Min. 3Kg |
){kind=link}